diff options
Diffstat (limited to 'doc/thesis')
| -rw-r--r-- | doc/thesis/chapters/implementation.tex | 17 | ||||
| -rw-r--r-- | doc/thesis/chapters/theory.tex | 2 |
2 files changed, 13 insertions, 6 deletions
diff --git a/doc/thesis/chapters/implementation.tex b/doc/thesis/chapters/implementation.tex index 04549c5..b2e5d72 100644 --- a/doc/thesis/chapters/implementation.tex +++ b/doc/thesis/chapters/implementation.tex @@ -70,14 +70,19 @@ Here its possible to add some AWGN noise in the channel line. Different paramete Discuss the multitap FIR model we used. How it is possible to set the delay etc. Also mathematics for the interpolation. } -To get a basic line for further simulations a 16QAM has been made. The results of this simulation are shown in \figref{fig:simul16QAM} and \figref{fig:simul16QAM_1} as the red Signal. In \tabref{tab:modulation_settings} some importer Parameter settings for a different modulation scheme are mentioned. - -A FIR-Filter was added in the Channel to create a time delay between tow paths. In \figref{fig:simul16QAM} the result includes a direct path and a delayed one. In the plot of \figref{fig:simul16QAM_1} the transmission line dosn't include a direct path. %It's impotent to mention that the delay should be smaller than the symbol rate or a multiple of it. (Stimmt dies , not sure any more) - -For the a first simulation with some fading the 16QAM simulation model has been extended with a FIR-Filter in the Chanel. The results of this simulation are shown in \figref{fig:simul16QAM} and \figref{fig:simul16QAM_1} as the blue Signal. +%To get a basic line for further simulations a 16QAM has been made. The results of this simulation are shown in \figref{fig:simul16QAM} and \figref{fig:simul16QAM_1} as the red Signal. In \tabref{tab:modulation_settings} some importer Parameter settings for a different modulation scheme are mentioned. +% +%A FIR-Filter was added in the Channel to create a time delay between tow paths. In \figref{fig:simul16QAM} the result includes a direct path and a delayed one. In the plot of \figref{fig:simul16QAM_1} the transmission line dosn't include a direct path. %It's impotent to mention that the delay should be smaller than the symbol rate or a multiple of it. (Stimmt dies , not sure any more) +% +%For the a first simulation with some fading the 16QAM simulation model has been extended with a FIR-Filter in the Chanel. The results of this simulation are shown in \figref{fig:simul16QAM} and \figref{fig:simul16QAM_1} as the blue Signal. +\subsection{Fading} %TO DO: übersetzen -Für das veranschaulichen des Fading effekts wurde ein eigener Block kreaiert und in den Channel implementiert. Dieser Block basiert auf einem FIR Filter. Es kann mit direcktem Pfad oder ohne dargestellt werden ( Line of Side ). Mit Hilfe des FIR filters wird die Verspätung der nebenpfaden dargestellt. Es ist möglich beliebig viele dieser Pfade mit unterschiedlicher stärke zu simulieren. +Für das veranschaulichen des Fading effekts wurde ein eigener Block kreaiert und in den Channel implementiert. Dieser Block basiert auf einem FIR Filter. Es kann mit direcktem Pfad oder ohne dargestellt werden ( Line of Side ). Mit Hilfe dieses Filters wird die Verspätung der nebenpfaden dargestellt. Es ist möglich beliebig viele dieser Pfade mit unterschiedlicher stärke zu simulieren. + +% Bild einfügen +\subsubsection{Fractional Delay} +Problem Werte nur auf dem Sample übermitelt und keine dazwischen. diff --git a/doc/thesis/chapters/theory.tex b/doc/thesis/chapters/theory.tex index 92dea24..520277d 100644 --- a/doc/thesis/chapters/theory.tex +++ b/doc/thesis/chapters/theory.tex @@ -273,6 +273,8 @@ multipath = tap(.8, 500e-9, f) + tap(.4, 300e-9, f) \subsection{Difficulties caused by discrete time} + + \skelpar{Not sampling at peaks of sincs.} \skelpar{Discrete frequency response. Discuss bins, etc.} |